Yamaha XT250D Page 70 Owner'S Manual Download

Page: 70 / 100

PERIODIC MAINTENANCE AND ADJUSTMENT

7-32

stallation.

NOTICE:

When install-

ing the battery, be sure the key
is turned to “OFF”, then con-
nect the positive lead before
connecting the negative
lead.

[ECA16840]

NOTICE

ECA16530

Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.

EAU53900

Replacing the fuses

The main fuse and the fuse boxes,
which contains the fuses for the individ-
ual circuits, are located behind panel C.
(See page 7-9.)

If a fuse is blown, replace it as follows.

1. Turn the key to “OFF” and turn off

the electrical circuit in question.

2. Remove the blown fuse, and then

install a new fuse of the specified
amperage.

WARNING! Do not

use a fuse of a higher amperage
rating than recommended to
avoid causing extensive dam-
age to the electrical system and
possibly a fire.

[EWA15131]

1. Fuse box 1

2. Fuse box 2

3. Main fuse

4. Spare main fuse

1. Spare fuse

2. Ignition fuse

3. Fuel injection system fuse

4. Spare fuse

5. Headlight fuse

6. Signaling system fuse

2 3

1YB-9-10.book 32 ページ２０１２年３月２７日　火曜日　午前１１時３６分

Summary of Contents for XT250D





































































































Search results

Summary of Contents for XT250D

Reviews:

Related manuals for XT250D

Brands by name

Popular brands

Yamaha XT250D, Owner'S Manual

Search results

Summary of Contents for XT250D

Reviews:

Related manuals for XT250D

Brands by name

Popular brands