Yamaha XT250D Page 61 Owner'S Manual Download | Manualshive

Page: 61 / 100

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-23

2

3

4

5

6

7

8

9

peared, have a Yamaha dealer replace
the brake pads as a set.

EAU36720

Rear brake pads

Each rear brake pad is provided with
wear indicator grooves, which allow
you to check the brake pad wear with-
out having to disassemble the brake.
To check the brake pad wear, check
the wear indicator grooves. If a brake
pad has worn to the point that the wear
indicator grooves have almost disap-
peared, have a Yamaha dealer replace
the brake pads as a set.

EAU22581

Checking the brake fluid level

Before riding, check that the brake fluid
is above the minimum level mark.
Check the brake fluid level with the top
of the reservoir level. Replenish the
brake fluid if necessary.

Front brake

Rear brake

WARNING

EWA15990

Improper maintenance can result in
loss of braking ability. Observe
these precautions:



Insufficient brake fluid may al-
low air to enter the brake sys-
tem, reducing braking
performance.



Clean the filler cap before re-
moving. Use only DOT 4 brake
fluid from a sealed container.



Use only the specified brake flu-
id; otherwise, the rubber seals

1. Wear indicator groove

1

1

1. Minimum level mark

1

1. Minimum level mark

Specified brake fluid:

DOT 4

1

1YB-9-10.book 23 ページ２０１２年３月２７日　火曜日　午前１１時３６分

«
...
59
60
61
62
63
...
»

Summary of Contents for XT250D





































































































Reviews:

No comments

Related manuals for XT250D

Indian eFTR Mini 2021

Brand: Razor Pages: 20

Brand: LSL Pages: 4

Brand: MSA Pages: 163

Brand: R&G Pages: 14

Brand: LAZER Pages: 19

Brand: Kong Pages: 72

Brand: Honda Pages: 41

Lock-it TANKRING 506003

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 7

Brand: SHERCO Pages: 102

Brand: Fantic Pages: 153

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 114

Brand: Yamaha Pages: 168

Brand: Yamaha Pages: 497

Brand: Yamaha Pages: 704

Brand: Yamaha Pages: 84

Brand: Magna Pages: 223

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands