Yamaha XT250D Page 45 Owner'S Manual Download

Page: 45 / 100

PERIODIC MAINTENANCE AND ADJUSTMENT

7-7

Sidestand pivot

• Check operation.
• Apply lithium-soap-based

grease lightly.



18 *

Sidestand switch

• Check operation and replace if

necessary.



19 *

Front fork

• Check operation and for oil

leakage.

• Replace if necessary.



20 *

Shock absorber
assembly

• Check operation and for oil

leakage.

• Replace if necessary.



21 *

Rear suspension
link pivots

• Check operation.
• Correct if necessary.



Engine oil

• Change (warm engine before

draining).



Engine oil filter
element

• Replace.



24 *

Front and rear
brake switches

• Check operation.



25 *

Control cables

• Apply Yamaha chain and cable

lube or engine oil thoroughly.



26 *

Throttle grip

• Check operation.
• Check throttle grip free play, and

adjust if necessary.

• Lubricate cable and grip

housing.



27 *

Lights, signals and
switches

• Check operation.
• Adjust headlight beam.



No.

ITEM

ROUTINE

INITIAL

ODOMETER READINGS

600 mi

(1000 km)

1 month

4000 mi

(6000 km)

6 months

7000 mi

(11000 km)

12 months

10000 mi

(16000 km)

18 months

13000 mi

(21000 km)

24 months

16000 mi

(26000 km)

30 months

1YB-9-10.book 7 ページ２０１２年３月２７日　火曜日　午前１１時３６分

Summary of Contents for XT250D





































































































Search results

Summary of Contents for XT250D

Reviews:

Related manuals for XT250D

Brands by name

Popular brands

Yamaha XT250D, Owner'S Manual

Search results

Summary of Contents for XT250D

Reviews:

Related manuals for XT250D

Brands by name

Popular brands