Yamaha XT250 2024 Owner'S Manual Download | Manualshive

Page: 60 / 96

background image

Periodic maintenance and adjustment

7-21

1

2

3

4

5

6

7

8

9

10

11

12

EAU22038

Adjusting the clutch lever free
play

Measure the clutch lever free play as
shown.

Periodically check the clutch lever free
play and, if necessary, adjust it as fol-
lows.

1. Slide the rubber cover back at the

clutch lever.

2. Loosen the locknut.
3. To increase the clutch lever free

play, turn the clutch lever free play
adjusting bolt in direction (a). To
decrease the clutch lever free play,
turn the adjusting bolt in direction
(b).

TIP

If the specified clutch lever free play
could be obtained as described above,
skip steps 4–8.

4. Fully turn the adjusting bolt in di-

rection (a) to loosen the clutch ca-
ble.

5. Slide the rubber cover back at the

clutch cable.

6. Loosen the locknut further down

the clutch cable.

7. To increase the clutch lever free

play, turn the clutch lever free play
adjusting nut in direction (a). To
decrease the clutch lever free play,
turn the adjusting nut in direction
(b).

8. Tighten the locknut at the clutch

cable, and then slide the rubber
cover to its original position.

9. Tighten the locknut at the clutch le-

ver, and then slide the rubber cov-
er to its original position.

1. Locknut (clutch lever)

2. Clutch lever free play adjusting bolt

3. Clutch lever free play adjusting nut

4. Rubber cover (clutch cable)

5. Locknut (clutch cable)

6. Rubber cover (clutch lever)

7. Clutch lever free play

Clutch lever free play:

10.0–15.0 mm (0.39–0.59 in)

1

2

(b)

(a)

(a)

(b)

7

3

4

5

6

6

B1U-9-75-E0.book 21 ページ２０２３年４月２０日　木曜日　午後１時５３分

«
...
58
59
60
61
62
...
»

Summary of Contents for XT250 2024

































































































Reviews:

No comments

Related manuals for XT250 2024

Brand: PACIFIC CYCLE Pages: 112

WARRIOR YFM350XS

Brand: Yamaha Pages: 46

Brand: Suzuki Pages: 206

Brand: GAS GAS Pages: 72

Brand: Dakota Digital Pages: 7

Brand: METRAKIT Pages: 53

MASTERFOX 125cc 2015

Brand: d'Magna Pages: 29

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 110

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 216

Brand: Yamaha Pages: 380

Brand: Yamaha Pages: 658

Brand: Yamaha Pages: 106

Brand: Royal Enfield Pages: 110

Brand: Tipperary Pages: 2

Brand: Smarter tools Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands