background image

Periodic maintenance and adjustment

7-13

1

2

3

4

5

6

7

8

9

10

11

12

EAU3780D

Engine oil and oil filter 
element

The engine oil level should be checked
regularly. In addition, the oil must be
changed and the oil filter element re-
placed at the intervals specified in the
periodic maintenance chart.

NOTICE

ECA11621

In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.

Make sure that no foreign mate-

rial enters the crankcase.

To check the engine oil level

1. Start the engine, warm it up for

several minutes, and then turn it
off.

2. Wait a few minutes until the oil lev-

el settles and with the vehicle on a
level surface, hold it upright for an
accurate reading.

3. Look at the check window located

at the bottom-right side of the
crankcase.

TIP

The engine oil should be between the

minimum and maximum level marks.

4. If the engine oil is at or below the

minimum level mark, remove the
oil filler bolt and add oil.

5. Check the engine oil filler bolt

O-ring. Replace if damaged.

6. Install the engine oil filler bolt.

To change the engine oil (and filter)

1. Start the engine, warm it up briefly,

and then turn it off.

2. Place an oil pan under the engine

to collect the used oil.

3. Remove the engine oil filler bolt,

and then the engine oil drain bolt
and gasket. 

Recommended engine oil:

See page 9-1.

Oil quantity:

Oil change:

1.20 L (1.27 US qt, 1.06 Imp.qt)

With oil filter removal:

1.30 L (1.37 US qt, 1.14 Imp.qt)

1. Engine oil level check window

2. Maximum level mark

3. Minimum level mark

2

3

1

1. Engine oil filler bolt

2. O-ring

2

1

B1U-9-75-E0.book  13 ページ  2023年4月20日 木曜日 午後1時53分

Summary of Contents for XT250 2024

































































































Reviews: