Yamaha XMAX 2022 Owner'S Manual Download Page 79

Page: 79 / 122

Perio

ic maintenance an

justment

8-17

case. The en

ine shoul

never

e operate

without the air filter

element installe

, otherwise the

piston(s) an

/or cylin

er(s) may

ecome excessively worn.

[ECA10482]

7. Pull the pre air filter element out,

and then blow out the dirt with
compressed air as shown.

8. Check the pre air filter element for

damage, and replace it if neces-
sary.

9. Insert the pre air filter element into

the air filter case cover.

10. Install the air filter case cover by

installing the screws.

TIP

The long screw should be installed as
shown.

11. Install the rubber plugs.

Cleanin

the V-

elt case air filter el-

ement

1. Place the vehicle on the center-

stand.

2. Remove the air filter case cover.

(See the previous section.)

3. Remove the V-belt case cover

screws.

1. Pre air filter element
2. Air filter case cover

1. Long screw

UB5X10E0.book Page 17 Thursday, May 27, 2021 8:55 AM

Summary of Contents for XMAX 2022



























































































































Search results

Summary of Contents for XMAX 2022

Reviews:

Related manuals for XMAX 2022

Brands by name

Popular brands

Yamaha XMAX 2022, Owner'S Manual

Search results

Summary of Contents for XMAX 2022

Reviews:

Related manuals for XMAX 2022

Brands by name

Popular brands