Yamaha XMAX 2022 Owner'S Manual Download Page 51

Page: 51 / 122

Instrument an

control functions

5-21

4. Install the windshield to the high

position by installing the bolts, and
then tighten the bolts to the spec-
ified torque.

WARNING! A loose

win

shiel

coul

cause an acci-

ent. Be sure to ti

hten the

screws to the specifie

torque.

[EWA15511]

5. Place the bolt access covers, and

then install the quick fasteners.

To chan

e the win

shiel

hei

ht to

the low position

1. Remove the bolt access covers by

removing the quick fasteners.

2. Remove the windshield by remov-

ing the bolts.

3. Remove the bolts, and then install

the bolts in the desired position.

1. Bolt

htenin

torque:

Windshield bolt:

8 N·m (0.8 kgf·m, 5.9 lb·ft)

1. Bolt access cover

UB5X10E0.book Page 21 Thursday, May 27, 2021 8:55 AM

Summary of Contents for XMAX 2022



























































































































Search results

Summary of Contents for XMAX 2022

Reviews:

Related manuals for XMAX 2022

Brands by name

Popular brands

Yamaha XMAX 2022, Owner'S Manual

Search results

Summary of Contents for XMAX 2022

Reviews:

Related manuals for XMAX 2022

Brands by name

Popular brands