Yamaha XMAX 2022 Owner'S Manual Download Page 38 | Manualshive

Page: 38 / 122

background image

Instrument an

d

control functions

5-8

5

The icy road warning indicator “ ” will
flash when the temperature is below 38
°F.
The temperature displayed may vary
from the actual ambient temperature.

TIP

The accuracy of the temperature read-
ing may be affected by engine heat
when riding slowly (under 20 km/h [12
mi/h]) or when stopped at traffic sig-
nals, etc.

Battery volta

g

e

d

isplay

This display shows the current charge
state of the battery.

TIP



If the engine turns over slowly
when using the start switch, have
a Yamaha dealer charge the bat-
tery.



If “---” appears in the battery volt-
age display, have a Yamaha deal-
er check the battery.

Traction control system

d

isplay

This display shows the current status
of the traction control system. (See
page 5-13.)



“TCS ON”: the system is on



“TCSOFF”: the system is off

TIP

If only “TCS” is displayed, there is a
communication error within the vehi-
cle. Have a Yamaha dealer check the
vehicle as soon as possible.

Avera

g

e fuel consumption

d

isplay

This function calculates the average
fuel consumption since it was last re-
set.
The average fuel consumption can be
displayed in “km/L”, “L/100 km” or
“MPG”.



“Consumption/Average km/L”:
The average distance that can be
traveled on 1.0 L of fuel is shown.

1. Battery voltage display

1

1. Traction control system display

1

1. Average fuel consumption display

1

UB5X10E0.book Page 8 Thursday, May 27, 2021 8:55 AM

«
...
36
37
38
39
40
...
»

Summary of Contents for XMAX 2022



























































































































Reviews:

No comments

Related manuals for XMAX 2022

Brand: LSL Pages: 4

Brand: MSA Pages: 163

Brand: R&G Pages: 15

Brand: hepco & becker Pages: 2

Brand: Can-Am Pages: 196

Brand: Cobra Pages: 80

Brand: Dakota Digital Pages: 11

Brand: hepco & becker Pages: 5

Brand: rizoma Pages: 16

V125 Special 2018

Brand: Lambretta Pages: 53

R 1200 R Classic

Brand: BMW Pages: 1

Brand: Yamaha Pages: 400

CIAK MASTER 50-4T

Brand: Malaguti Pages: 31

Brand: Beta Pages: 82

Brand: Beta Pages: 248

2008 URBAN 125cc

Brand: Beta Pages: 370

Brand: Abus Pages: 18

Brand: Bushtec Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands