manualshive.com logo in svg

Yamaha XJ6N, Owner'S Manual

Share
Download
Yamaha XJ6N Owner'S Manual Download Page 88

PERIODIC MAINTENANCE AND ADJUSTMENT

6-43

6

4. Lower the front wheel so that it is

on the ground, and then put the
sidestand down.

5. Tighten the wheel axle, the front

wheel axle pinch bolt and the
brake caliper bolts to the specified
torques.

6. Push down hard on the handlebar

several times to check for proper
fork operation.

EAU44801

Rear wheel (for non-ABS mod-
els) 

WARNING

EWA14840

For the ABS model, have a Yamaha
dealer remove and install the wheel.

EAU34414

To remove the rear wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Loosen the locknut and drive chain

slack adjusting nut on each side of
the swingarm.

2. Loosen the axle nut.

3. Lift the rear wheel off the ground

according to the procedure on
page 6-41.

4. Remove the axle nut.
5. Push the wheel forward, and then

remove the drive chain from the
rear sprocket.

Tightening torques:

Wheel axle:

65 Nm (6.5 m·kgf, 47 ft·lbf)

Front wheel axle pinch bolt:

19 Nm (1.9 m·kgf, 14 ft·lbf)

Brake caliper bolt:

40 Nm (4.0 m·kgf, 29 ft·lbf)

1. Axle nut
2. Drive chain slack adjusting nut

3. Locknut

1

3

2

U20SE3E0.book  Page 43  Monday, April 23, 2012  10:47 AM

Summary of Contents for XJ6N









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands