Yamaha XJ6N Owner'S Manual Download | Manualshive

Page: 19 / 104

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-4

3

EAU49391

Indicator lights and warning
lights

EAU11020

Turn signal indicator light “

”

This indicator light flashes when the
turn signal switch is pushed to the left or
right.

EAU11060

Neutral indicator light “

”

This indicator light comes on when the
transmission is in the neutral position.

EAU11080

High beam indicator light “

”

This indicator light comes on when the
high beam of the headlight is switched
on.

EAU11254

Oil level warning light “

”

This warning light comes on if the en-
gine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.

TIP

●

Even if the oil level is sufficient, the
warning light may flicker when
riding on a slope or during sudden
acceleration or deceleration, but
this is not a malfunction.

●

This model is also equipped with a
self-diagnosis device for the oil
level detection circuit. If a problem
is detected in the oil level detection
circuit, the following cycle will be
repeated until the malfunction is
corrected: The oil level warning
light will flash ten times, then go off
for 2.5 seconds. If this occurs,
have a Yamaha dealer check the
vehicle.

EAU1142A

Coolant temperature warning
light “

”

This warning light comes on if the en-
gine overheats. If this occurs, stop the
engine immediately and allow the en-
gine to cool.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.

1. Turn signal indicator light “

”

2. Immobilizer system indicator light
3. Neutral indicator light “

”

4. High beam indicator light “

”

5. Engine trouble warning light “

”

6. Oil level warning light “

”

7. Coolant temperature warning light “

”

8. Anti-lock Brake System (ABS) warning

light “

” (for ABS models)

ABS

1

2

3 4 5

7 6

8

ABS

U20SE3E0.book Page 4 Monday, April 23, 2012 10:47 AM

«
...
17
18
19
20
21
...
»

Summary of Contents for XJ6N









































































































Reviews:

No comments

Related manuals for XJ6N

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 44

Brand: HYOSUNG Pages: 98

Brand: Honda Pages: 201

Brand: Ohlins Pages: 8

Brand: Suzuki Pages: 42

KAWASAKI ZX6R 2007/8

Brand: Evotech Performance Pages: 2

SCARABEO 100 4T - 06-2001 PART6

Brand: APRILIA Pages: 6

B-TRK502-01-01-SL

Brand: SRC Pages: 5

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 116

Tracer 9 GT 2021

Brand: Yamaha Pages: 126

Brand: Yamaha Pages: 116

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 116

Brand: Yamaha Pages: 87

Brand: Vanucci Pages: 35

METEOR 350 2021

Brand: Royal Enfield Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands