manualshive.com logo in svg

Yamaha XJ6N, Owner'S Manual

Share
Download
Yamaha XJ6N Owner'S Manual Download Page 79

PERIODIC MAINTENANCE AND ADJUSTMENT

6-34

6

is turned to “OFF”, then con-
nect the positive lead before
connecting the negative lead.

[ECA16840]

4. After installation, make sure that

the battery leads are properly con-
nected to the battery terminals.

NOTICE

ECA16530

Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.

EAU47172

Replacing the fuses 

The main fuse and the fuse boxes,
which contain the fuses for the individu-
al circuits, are located under the seat.
(See page 3-18.)

TIP

To access the main fuse, remove the
starter relay cover as shown.

XJ6N

XJ6N

1. Starter relay cover

2. Main fuse
3. Spare main fuse

4. Fuse box

2

4

3

1

1. Taillight fuse

2. Spare fuse

3. Headlight fuse
4. Ignition fuse

5. Signaling system fuse

6. Backup fuse (for clock and immobilizer sys-

tem)

7. Fuel injection system fuse

8. Radiator fan fuse

1

2

3

4

5

6

7

8

U20SE3E0.book  Page 34  Monday, April 23, 2012  10:47 AM

Summary of Contents for XJ6N









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands