background image

 

Basic components

 

16

 

 

” 

 

(start)

 

With the main switch in the “

” (start) po-

sition, the starter motor turns to start the en-
gine. When the key is released, it returns
automatically to the “

” (on) position.

 

EMU26141

 

Power trim and tilt switch on remote 
control or tiller handle

 

The power trim and tilt system adjusts the
outboard motor angle in relation to the tran-
som. Pressing the switch “

” (up) trims the

outboard motor up, then tilts it up. Pressing
the switch “

” (down) tilts the outboard mo-

tor down and trims it down. When the switch
is released, the outboard motor will stop in its
current position.

NOTE:

 

For instructions on using the power trim and

 

tilt switch, see pages 42 and 44.

 

EMU26151

 

Power trim and tilt switch on bottom 
engine cowling

 

The power trim and tilt switch is located on
the side of the bottom engine cowling. Press-
ing the switch “

” (up) trims the outboard

motor up, then tilts it up. Pressing the switch

” (down) tilts the outboard motor down

and trims it down. When the switch is re-
leased, the outboard motor will stop in its
current position.

WARNING

 

EWM01030 

 

Use the power trim and tilt switch located
on the bottom engine cowling only when
the boat is at a complete stop with the en-
gine off. Attempting to use this switch
while the boat is moving could increase
the risk of falling overboard and could
distract the operator, increasing the risk
of collision with another boat or an obsta-

 

cle.

NOTE:

 

For instructions on using the power trim and

 

tilt switch, see page 44.

 

EMU26241

 

Trim tab with anode

 

The trim tab should be adjusted so that the
steering control can be turned to either the
right or left by applying the same amount of

UP

DN

ZMU01862

Summary of Contents for VZ200



























































































Reviews: