Yamaha VZ150 Owner'S Manual Download | Manualshive

Page: 32 / 92

background image

Basic components

26

ous engine damage will occur.

●

Do not continue to operate the engine if
a warning device has activated. Con-
sult your Yamaha dealer if the problem

cannot be located and corrected.

Water separator warning

This indicator will blink when water has accu-
mulated in the water separator (fuel filter)
while cruising. In such an event, stop the en-
gine immediately and see page 70 of this
manual to drain the water from the fuel filter.
Get back to the port soon and consult a
Yamaha dealer immediately.

CAUTION:

ECM00910

Gasoline mixed with water could cause

damage to the engine.

Engine trouble warning

This indicator will blink when the engine mal-
functions while cruising. Get back to the port

soon and consult a Yamaha dealer immedi-
ately.

CAUTION:

ECM00920

In such an event, the engine will not oper-
ate properly. Consult a Yamaha dealer

immediately.

Low battery voltage warning

When the battery voltage drops, the low bat-
tery voltage warning indicator and the bat-
tery voltage value will start to blink. Get back
to the port soon if the low battery voltage
warning device has activated. For charging
the battery, consult your Yamaha dealer.

ZMU05423

ZMU05424

ZMU05425

ZMU05426

«
...
30
31
32
33
34
...
»

Summary of Contents for VZ150





























































































Reviews:

No comments

Related manuals for VZ150

TLV320AIC3111 EVM

Brand: Texas Instruments Pages: 39

Brand: Aaeon Pages: 40

MBATX-845GV-VEAH

Brand: Kontron Pages: 70

GeForce 8300 (MI-A78U-8309)

Brand: XFX Pages: 26

Brand: BCM Pages: 5

Brand: Freetech Pages: 79

Brand: Texas Instruments Pages: 16

Brand: Vox Pages: 23

Brand: IBASE Technology Pages: 91

Brand: Gigabyte Pages: 36

z170a GAMING M9 ACK

Brand: MSI Pages: 109

Brand: ASROCK Pages: 40

EV MOD CH101-01-02

Brand: TDK Pages: 10

Brand: CHAINTECH Pages: 49

Brand: WinSystems Pages: 16

Brand: ASROCK Pages: 162

BOOSTXL-DRV8301

Brand: Texas Instruments Pages: 13

Brand: Texas Instruments Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands