background image

 

General information

 

4

 

the switch, stopping the engine.

 

 

Know the marine laws and regulations
where you will be boating—and obey
them. For basic boating rules, see “Rules
of the road” on page 5.

 

 

Stay informed about the weather. Check
weather forecasts before boating. Avoid
boating in hazardous weather.

 

 

Tell someone where you are going: leave
a Float Plan with a responsible person. Be
sure to cancel the Float Plan when you re-
turn.

 

 

Use common sense and good judgment
when boating. Know your abilities, and be
sure you understand how your boat han-
dles under the different boating conditions
you may encounter. Operate within your
limits, and the limits of your boat. Always
operate at safe speeds, and keep a careful
watch for obstacles and other traffic.

 

 

Always watch carefully for swimmers dur-
ing the engine operation.

 

 

Stay away from swimming areas.

 

 

When a swimmer is in the water near you
shift into neutral and shut off the engine.

 

 

Do not illegally discard empty containers
used to replace or replenish oil. For the
correct processing of empty containers,
consult the dealer where you purchased
the oil.

 

 

When replacing oils used to lubricate the
product (engine or gear oil), be sure to
wipe away any spilt oil. Never pour oil with-
out using a funnel or similar device. If nec-
essary, verify the necessary replacement
procedure with the dealer.

 

 

Never illegally discard (dump) the product.
Yamaha recommends consulting the deal-
er on discarding the product.

Be informed about boating safety. Additional
publications and information can be obtained

from many organizations, including the fol-
lowing:

 

United States Coast Guard

 

Consumer Affairs Staff (G-BC)
 Office of Boating, Public, and Consumer Af-
fairs
 U.S. Coast Guard Headquarters
 Washington, D.C. 20593-0001
 Boating Safety Hotline: 1-800-368-5647

 

National Marine Manufacturers Associa-
tion (NMMA)

 

401 N. Michigan Ave.
 Chicago, Il 60611

 

Marine Retailers Association of America

 

155 N. Michigan Ave.
 Chicago, Il 60601

 

EMU25382

 

Important labels

 

EMU25395

 

Warning labels

ZMU04890

ZMU01948

Summary of Contents for VZ150





























































































Reviews: