manualshive.com logo in svg

Yamaha VZ150, Owner'S Manual

Share
Download
Yamaha VZ150 Owner'S Manual Download Page 26

 

Basic components

 

20

 

EMU26581

 

Overheat warning indicator (digital 
type)

 

If the engine temperature rises too high, the
warning indicator will start to blink. For fur-
ther information on reading the indicator, see
page 29.

CAUTION:

 

ECM00050 

 

Do not continue to run the engine if the
overheat warning indicator is on. Serious

 

engine damage will occur.

 

EMU26600

 

Speedometer (digital type)

 

This gauge shows the boat speed.

NOTE:

 

After the main switch is first turned on, all
segments of the display come on as a test.
After a few seconds, the gauge will change
to normal operation. Watch the gauge when
turning on the main switch to make sure all

 

segments come on.

NOTE:

 

The speedometer displays km/h, mph, or
knots, according to operator preference. Se-
lect the desired unit of measurement by set-
ting the selector switch on the back of the

 

gauge. See the illustration for settings.

 

1. Oil level indicator

1. Overheat warning indicator

1

ZMU01867

1

ZMU01868

 

1. Speedometer
2. Fuel gauge
3. Trip meter/clock/voltmeter
4. Warning indicator(s)

1. Cap
2. Selector switch (for speed unit)

Summary of Contents for VZ150





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands