Yamaha VX150A Owner'S Manual Download Page 91

Page: 91 / 118

4-26

901014*

t y

Use of smaller wire could lead to a fire.

Battery for starting

Battery for accessories

Large red lead for starting battery

Small red lead for accessory battery
charging (optional part)

Large black lead

Negative connecting cable

NOTE:

If a battery selector switch is desired, con-
sult your YAMAHA dealer about correct
wiring.

EMU01280

Disconnecting the Battery

Disconnect the BLACK lead from the NEG-
ATIVE (-) terminal first. Then disconnect
the RED lead from the POSITIVE (+) termi-
nal.

EMU00408

CHECKING BOLTS AND NUTS

Check that bolts securing the cylinder
head and engine and the nut securing
the flywheel are tightened with their
specified tightening torque.

Check the tightening torque of other
bolts and nuts.

EMU00409

MOTOR EXTERIOR

EMU00410

Cleaning the Outboard Motor

After use, wash the exterior of the out-
board with fresh water.
Flush the cooling system with fresh
water.

NOTE:

Refer to Flushing Cooling System instruc-
tions in “TRANSPORTING AND STORING
OUTBOARD MOTOR”.

Summary of Contents for VX150A























































































































Search results

Summary of Contents for VX150A

Reviews:

Related manuals for VX150A

Brands by name

Popular brands

Yamaha VX150A, Owner'S Manual

Search results

Summary of Contents for VX150A

Reviews:

Related manuals for VX150A

Brands by name

Popular brands