Yamaha VX150A Owner'S Manual Download Page 40

Page: 40 / 118

EMU00172

OIL LEVEL WARNING / OIL FILTER
CLOGGING WARNING

This engine has an oil level warning sys-
tem. If oil level falls below lower limit, the
warning device will activate.

(

); Included (—); N/A

If the warning system has been activated,
stop the engine and check for the cause.

NOTE:

The warning for oil filter clogging is simi-
lar to the warnings for low oil level and
overheating. For easy troubleshooting, it
is advisable to check for engine overheat-
ing first, then oil level and finally oil filter
clogging.

Oil filter

2-19

001054

213022

905012

Warning device

Tiller

Remote

activation

control

model

The engine speed
will automatically

decrease to about
2,000 r/min.

The oil level warning

indicator will come on.

The buzzer will sound.

701054

Summary of Contents for VX150A























































































































Search results

Summary of Contents for VX150A

Reviews:

Related manuals for VX150A

Brands by name

Popular brands

Yamaha VX150A, Owner'S Manual

Search results

Summary of Contents for VX150A

Reviews:

Related manuals for VX150A

Brands by name

Popular brands