Yamaha VX150A Owner'S Manual Download Page 7

Page: 7 / 118

1-2

EMU01385

EMISSION CONTROL

INFORMATION

EMU01386

NORTH AMERICAN MODELS

This engine conforms to U.S.
Environmental Protection Agency (EPA)
regulations for marine SI engines. See the
label affixed to your engine for details.

Approval label of Emission control
certificate

This label is attached to the bottom cowl-
ing.

Emission control information label

Existing Technology ; N/A

Manufactured date label

This label is attached to the clamp bracket
or the swivel bracket.

Manufactured date label

EMISSION CONTROL INFORMATION

ENGINE FAMILY :

THIS ENGINE CONFORMS TO 2001 U.S. EPA REGULATIONS FOR MARINE SI ENGINES.
FELs :
SPARK PLUG :

IDLE SPEED :

rpm IN NEUTRAL

SPARK PLUG GAP (mm) :

g/kw-hr

Manufactured:

Summary of Contents for VX150A























































































































Search results

Summary of Contents for VX150A

Reviews:

Related manuals for VX150A

Brands by name

Popular brands

Yamaha VX150A, Owner'S Manual

Search results

Summary of Contents for VX150A

Reviews:

Related manuals for VX150A

Brands by name

Popular brands