background image

602073

q

w

e

r

t

y

6

5

4

3

2

1

602041*

4-22

E

EML08011

CHECKING PROPELLER

w

You could be seriously injured if the
engine accidentally starts while you are
near the propeller.

8

Before inspecting, removing or
installing the propeller, remove the
spark plug caps from the spark plugs.
Also, put the shift control in Neutral,
put the main switch in the “OFF” posi-
tion and remove the key, and remove
the lanyard from the engine stop
switch. Turn off the battery cut-off
switch if your boat has one.

8

Do not use your hand to hold the pro-
peller when loosening or tightening the
propeller nut. Put a wood block
between the cavitation plate and the
propeller to prevent the propeller from
turning.

1)

Check each of the propeller blades for
wear, erosion from cavitation or ven-
tilation, or other damage.

2)

Check the splines for wear and dam-
age.

3)

Check for fish line winding around the
propeller shaft. Check the propeller
shaft oil seal for damage.

EMU00976

Removing the Propeller

1)

Straighten the cotter-pin 

1

and pull it

out using a pair of pliers.

2)

Remove the propeller nut 

2

, washer

3

and spacer 

4

.

3)

Remove the propeller 

5

and thrust

washer 

6

.

000964

602051

602054

F50/F60

T50/T60

 62Y-9-1C-4  3/20/03 10:25 AM  Page 23

Summary of Contents for T-50C



















































































































Reviews: