Yamaha T-50C Owner'S Manual Download

Page: 96 / 114

5-3

D. Warning buzzer

sounds or

indicator lamp

lights.

Trouble

Possible Cause

Remedy

1. Cooling system clogged.

2. Engine oil level low.

3. Heat range of spark plug incorrect.

4. Specified engine oil not used.

5. Engine oil contaminated or

deteriorated.

6. Oil filter clogged.

7. Oil feed/injection pump

malfunctions.

8. Load on boat improperly distributed.

9. Water pump/thermostat faulty.

1. Check water intake for restriction.

2. Fill oil tank with specified engine

oil.

3. Inspect spark plug and replace it

with recommended type.

4. Check and replace oil with

specified type.

5. Replace oil with fresh, specified

type.

6. Have serviced by a Yamaha

dealer.

7. Have serviced by a Yamaha

dealer.

8. Distribute load to place boat on an

even plane.

9. Have serviced by a Yamaha

dealer.

1. Propeller damaged.

2. Propeller pitch or diameter incorrect.

3. Trim angle incorrect.

4. Motor mounted at incorrect height

on transom.

5. Warning system activated.

6. Boat bottom fouled with marine

growth.

7. Spark plug(s) fouled or incorrect

type.

8. Weeds or other foreign matter

tangled on gear housing.

9. Fuel system obstructed.

10. Fuel filter clogged.

11. Fuel contaminated or stale.

12. Spark plug gap incorrect.

1. Have propeller repaired or

replaced.

2. Install correct propeller to operate

outboard at its recommended

speed (r/min) range.

3. Adjust trim angle to achieve most

efficient operation.

4. Have motor adjusted to proper

transom height.

5. Find and correct cause of warning.

6. Clean boat bottom.

7. Inspect spark plug(s). Clean or

replace with recommended type.

8. Remove foreign matter and clean

lower unit.

9. Check for pinched or kinked fuel

line or other obstructions in fuel

system.

10. Clean or replace filter.

11. Fill tank with clean, fresh fuel.

12. Inspect and adjust as specified.

E. Engine power loss.

62Y-9-1C-5 3/20/03 10:25 AM Page 4

Summary of Contents for T-50C



















































































































Search results

Summary of Contents for T-50C

Reviews:

Related manuals for T-50C

Brands by name

Popular brands

Yamaha T-50C, Owner'S Manual

Search results

Summary of Contents for T-50C

Reviews:

Related manuals for T-50C

Brands by name

Popular brands