Yamaha RX-V459 - AV Receiver - 6.1 Channel Owner'S Manual Download Page 100

Page: 100 / 111

TROUBLESHOOTING

■

Remote control

Problem

Cause

Remedy

See

page

The remote control
does not work nor
function properly.

Wrong distance or angle.

The remote control functions within a maximum
range of 6 m (20 ft) and no more than 30 degrees off-
axis from the front panel.

Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.

Reposition this unit.

—

The batteries are weak.

Replace all batteries.

The remote control code is not correctly
set.

Set the remote control code correctly using “LIST OF
REMOTE CONTROL CODES” at the end of this
manual.

Try setting another code for the same manufacturer
using “LIST OF REMOTE CONTROL CODES” at
the end of this manual.

The library code of the remote control and
the remote control ID of this unit do not
match.

Match the remote control ID of this unit with the
corresponding remote control library code.

85, 89

Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.

Summary of Contents for RX-V459 - AV Receiver - 6.1 Channel
















































































































Search results

Summary of Contents for RX-V459 - AV Receiver - 6.1 Channel

Reviews:

Related manuals for RX-V459 - AV Receiver - 6.1 Channel

Brands by name

Popular brands

Yamaha RX-V459 - AV Receiver - 6.1 Channel, Owner'S Manual

Search results

Summary of Contents for RX-V459 - AV Receiver - 6.1 Channel

Reviews:

Related manuals for RX-V459 - AV Receiver - 6.1 Channel

Brands by name

Popular brands