manualshive.com logo in svg

Yamaha Raptor YFM35RA, Owner'S Manual

Share
Download
Yamaha Raptor YFM35RA Owner'S Manual Download Page 93

8-21

8

TIP

The engine is warm when it quickly responds to the
throttle.

2. Attach the tachometer to the spark plug lead.
3. Check the engine idling speed and, if neces-

sary, adjust it to specification by turning the
throttle stop screw at the carburetor. To in-
crease the engine idling speed, turn the throt-
tle stop screw in direction (a), and to decrease
it, turn the screw in direction (b).

TIP

If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

EBU24045

Adjusting the throttle cable free play 

The throttle cable free play should be checked
and, if necessary, adjusted at the intervals speci-
fied in the periodic maintenance and lubrication
chart.
The throttle cable free play should measure 2.0–
4.0 mm (0.08–0.16 in) at the throttle lever. Period-
ically check the throttle cable free play and, if nec-
essary, adjust it as follows.

TIP

The engine idling speed must be checked, and ad-
justed if necessary, before adjusting the throttle ca-
ble free play.

1. Slide the rubber cover back.
2. Loosen the locknut.
3. To increase the throttle cable free play, turn

the throttle cable free play adjusting bolt in di-
rection (a). To decrease the throttle cable free
play, turn the adjusting bolt in direction (b).

1. Throttle stop screw

Engine idling speed:

1450–1550 r/min

U1BS11E0.book  Page 21  Monday, April 5, 2010  8:56 AM

Summary of Contents for Raptor YFM35RA















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands