manualshive.com logo in svg

Yamaha Raptor YFM35RA, Owner'S Manual

Share
Download
Yamaha Raptor YFM35RA Owner'S Manual Download Page 54

7-5

7

Do not operate after or while consuming alco-
hol or drugs.

The operator’s performance capability is reduced
by the influence of alcohol or drugs. Consuming al-
cohol or drugs could seriously affect your judg-
ment, cause you to react more slowly, and affect
your balance and perception. 

WARNING! Never

consume alcohol or drugs before or while driv-
ing this ATV. You increase your chance of an
accident.

 [EWB01421]

Pre-operation checks

Always inspect your ATV each time you use it to
make sure the ATV is in safe operating condition.
Perform the pre-operation checks listed on page
5-1. Always follow the inspection and maintenance
procedures and schedules described in the Own-
er’s Manual. 

WARNING! Failure to inspect the

ATV before operating it and to maintain it prop-
erly increases the possibility of an accident or
equipment damage.

 [EWB01431]

Speed limiter

For riders less experienced with this model, the
throttle lever housing is equipped with a speed lim-
iter. The speed limiter keeps the throttle from fully

1. Protective clothing
2. Goggles

3. Gloves

4. Boots
5. Helmet

U1BS11E0.book  Page 5  Monday, April 5, 2010  8:56 AM

Summary of Contents for Raptor YFM35RA















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands