Yamaha PW-SE series Original Instructions Manual Download Page 36

Page: 36 / 60

BATTERY PACK AND CHARGING PROCEDURE

The battery pack equipped for the Yamaha e-Bike Sys-

tems is a lithium-ion battery. The lithium-ion battery is

lightweight and offers superior capacity. However, it does

have the following characteristics.

• Its performance decreases in extremely hot or cold en-

vironments.

• It naturally loses its charge.

The battery pack for the Yamaha e-Bike Systems also has

an embedded computer which notifies you of estimated

residual battery capacity and suspected faults via the bat-

tery capacity indicator lamp.

By pressing the battery capacity indicator button, you can

display the residual battery capacity for approximately 5

seconds.

See “CHECKING THE RESIDUAL BATTERY CAPACITY”

for the estimate of the residual battery capacity. See

“TROUBLESHOOTING” for information on fault flashing.

Charging connector

Charging plug

Battery capacity

indicator lamp

Battery charger lamp

Charger

display

Battery

capacity

indicator

Battery capacity

indicator button

Power plug

Charging connector

Battery capacity

indicator lamp

Battery capacity

indicator button

Battery

capacity

indicator

Summary of Contents for PW-SE series





























































Search results

Summary of Contents for PW-SE series

Reviews:

Related manuals for PW-SE series

Brands by name

Popular brands

Yamaha PW-SE series, Original Instructions Manual

Search results

Summary of Contents for PW-SE series

Reviews:

Related manuals for PW-SE series

Brands by name

Popular brands