background image

3-13

SPARK PLUG INSPECTION/

IGNITION TIMING CHECK

INSP

ADJ

18 Nm (1.8 m

S

kg)

NOTE:

NOTE:

*****************************************************

*****************************************************

Spark plug gap:

0.6 

 0.7 mm

6. Install:

D

Spark plug

Before installing a spark plug, clean the gasket
surface and plug surface.

YP303052

IGNITION TIMING CHECK

Prior to checking the ignition timing, check all
electrical connections related to the ignition
system. Make sure all connections are tight and
free of corrosion and that all ground connec-
tions are tight.

1. Remove:

D

Timing check plug

2. Attach:

D

Timing light 

1

Engine tachometer 

2

(to the spark plug lead)

Timing light:

90890-03141

Engine tachometer:

90890-03113

3. Check:

D

Ignition timing

Checking steps:

D

Start the engine and let it warm up for several
minutes. Let the engine run at the specified
speed.

Engine idling speed:

1,450 

 1,550 r / min

D

Visually check the stationary pointer 

a

 to

verify it is within the required firing range 

b

indicated on the flywheel.
Incorrect firing range 

 Check the ignition

system.

Summary of Contents for MAJESTY YP250












































































































































































































































































Reviews: