Yamaha LZ250B Owner'S Manual Download Page 69

Page: 69 / 126

3-18

EMU00273

STOPPING ENGINE

Let it cool off for a few minutes at idle or low
speed first. Stopping the engine immediate-
ly after operating at high speed is not rec-
ommended.

EMU01199

Turn the main switch to “OFF”.

If  there  is  a  fuel  joint  or  a  fuel  cock  on
the  boat,  disconnect  the  fuel  line  or
close  the  fuel  cock  after  stopping  the
engine.

Tighten the air vent screw on the fuel
tank cap after stopping the engine, if it
is equipped.

Remove the key if the boat will be left
unattended.

NOTE:

The  engine  can  also  be  stopped  by  pulling
the  lanyard  and  removing  the  lock  plate
from  the  engine  stop  lanyard  switch  (then
turning the main switch to “OFF”).

START

OFF

701023

OFF

703046

60V-9-11-3 7/31/02 1:52 PM Page 19

Summary of Contents for LZ250B































































































































Search results

Summary of Contents for LZ250B

Reviews:

Related manuals for LZ250B

Brands by name

Popular brands

Yamaha LZ250B, Owner'S Manual

Search results

Summary of Contents for LZ250B

Reviews:

Related manuals for LZ250B

Brands by name

Popular brands