Yamaha LZ250B Owner'S Manual Download Page 46 | Manualshive

Page: 46 / 126

background image

E

2-21

EMU00157

TILT SUPPORT LEVER

To keep the outboard motor in the tilted-up
position, lock the tilt support lever to the
clamp bracket.

EMU00163

TOP COWLING LOCK LEVERS

To  remove  the  engine  top  cowling,  pull  up
the  front  and  rear  lock  levers. Then  lift  off
the  cowling. When  replacing  the  cowling,
check to be sure it fits properly in the rubber
seal. Then lock the cowling again by moving
the levers downward.

001571

001572

EMU01701

FLUSHING DEVICE

This device

1

is used to clean the cooling

water passages of the motor using a garden
hose and tap water.

NOTE:

Refer to “CLEANING COOLING-WATER
PASSAGES” in Chapter 4 for instructions on
usage.

001573

q

60V-9-11-2 7/31/02 10:26 AM Page 22

«
...
44
45
46
47
48
...
»

Summary of Contents for LZ250B































































































































Reviews:

No comments

Related manuals for LZ250B

Brand: J&W Pages: 40

Brand: NXP Semiconductors Pages: 269

Brand: MSI Pages: 91

Brand: BCM Pages: 3

Brand: Ublox Pages: 25

Brand: OpenVox Pages: 29

Brand: MSI Pages: 22

Brand: JETWAY Pages: 40

Brand: Quick Pages: 28

Brand: Microchip Technology Pages: 89

VVDI Mini Key Tool

Brand: Xhorse Pages: 17

Brand: Mercury Pages: 57

Brand: Biostar Pages: 210

Brand: Semtech Pages: 16

Brand: Ublox Pages: 22

Brand: Intel Pages: 87

GA-HA65M-D2H-B3

Brand: Gigabyte Pages: 104

MOTORKIT-91F267-MC

Brand: Fujitsu Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands