Yamaha KODIAK Ultramatic Owner'S Manual Download Page 78 | Manualshive

Page: 78 / 185

background image

7-10

WARNING

_

Indicates a potential hazard that could
result in serious injury or death.

Do not operate at speeds too fast for your
skills or the conditions.

Speed limiter

For riders less experienced with this model,
this model is equipped with a speed limiter in
the throttle lever housing. The speed limiter
keeps the throttle from fully opening, even
when the throttle lever is pushed to the maxi-
mum. Turning the adjusting screw in limits the
maximum engine power available and de-
creases the maximum speed of the ATV.
Turning the adjusting screw in decreases the
top speed and turning it out increases the top
speed.

1. Locknut

2. Adjusting screw

WARNING

POTENTIAL HAZARD
Operating this ATV at speeds too fast
for your skills or the conditions.
WHAT CAN HAPPEN
Increases your chances of losing con-
trol of the ATV, which can result in an
accident.
HOW TO AVOID THE HAZARD
Always go at a speed that is proper for
the terrain, visibility and operating con-
ditions, and your experience.

U5VH10.book Page 10 Thursday, May 16, 2002 2:18 PM

«
...
76
77
78
79
80
...
»

Summary of Contents for KODIAK Ultramatic


























































































































































































Reviews:

No comments

Related manuals for KODIAK Ultramatic

Brand: OTIS Pages: 17

Brand: Cectec Pages: 212

Honey Joy TY324116

Brand: Costway Pages: 7

Sportsman 850 Touring EPS

Brand: Polaris Pages: 510

Brand: Global Pages: 11

Brand: Panoz Pages: 67

MKII 600 Series

Brand: NC ENGINEERING Pages: 80

Brand: HAPERT Pages: 45

Brand: Can-Am Pages: 423

Brand: MANCO Pages: 16

Brand: Yamaha Pages: 54

Brand: Yamaha Pages: 134

Grizzly 450 YFM45FGPD

Brand: Yamaha Pages: 172

INTIMIDATOR XD 4

Brand: DFK Pages: 84

1990 DS Gasoline Golf Car

Brand: Club Car Pages: 20

Brand: Club Car Pages: 44

Brand: Swisher Pages: 4

2009 Sportsman X2 500 EFI

Brand: Polaris Pages: 148

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands