Yamaha KODIAK Ultramatic Owner'S Manual Download Page 41 | Manualshive

Page: 41 / 185

background image

4-19

EBU01002

Auxiliary DC jack

The auxiliary DC jack is located at the front
right side of the ATV. The auxiliary DC jack
can be used for suitable work lights, radios,
etc. The auxiliary DC jack should only be used
when the engine is running.

1. Set the light switch to “OFF”.

1. Auxiliary DC jack cap

2. Start the engine. (See pages 6-1–6-3.)
3. Open the auxiliary DC jack cap, and then

insert the accessory power plug into the
jack.

4. When the auxiliary DC jack is not being

used, cover it with the cap.

CAUTION:

_

●

Do not use accessories requiring
more than the above maximum capac-
ity. This may overload the circuit and
cause the fuse to blow.

●

If accessories are used without the
engine running or with the headlights
turned on, the battery will lose its
charge and engine starting may be-
come difficult.

●

Do not use an automotive cigarette
lighter or other accessories with a
plug that gets hot because the jack
can be damaged.

_

Maximum rated capacity for the auxiliary
DC jack:

DC 12 V, 120 W (10 A)

U5VH10.book Page 19 Thursday, May 16, 2002 2:18 PM

«
...
39
40
41
42
43
...
»

Summary of Contents for KODIAK Ultramatic


























































































































































































Reviews:

No comments

Related manuals for KODIAK Ultramatic

Brand: XY Powersports Pages: 259

Brand: Yamaha Pages: 26

Brand: Yamaha Pages: 130

Brand: Yamaha Pages: 116

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 154

Brand: Yamaha Pages: 160

Brand: Yamaha Pages: 162

Brand: Yamaha Pages: 184

Brand: Yamaha Pages: 328

Brand: Yamaha Pages: 409

Brand: Yamaha Pages: 128

Brand: Erde Pages: 4

Brand: TOMCAR Pages: 22

ESCALATE TRAILER ET 5000W

Brand: Bil-Jax Pages: 20

Brand: Labrie Pages: 36

Brand: Qlink Pages: 74

Brand: Landoll Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands