Yamaha KODIAK Ultramatic Owner'S Manual Download Page 26

Page: 26 / 185

4-4

EBU00052

Fuel gauge

The fuel gauge indicates the amount of fuel in
the fuel tank. When the needle reaches the
red line, refill the tank at the first opportunity.

1. Fuel gauge

2. Red line

NOTE:

If the machine runs out of fuel, move the fuel
cock lever to the “RES” position. Approxi-
mately 4.5 L (0.99 Imp gal, 1.19 US gal) of
fuel will be remaining in the tank.

EBU00053

Handlebar switches

1. Light switch “

/OFF”

2. Engine stop switch “

”

3. Start switch “

”

EBU01251

Light switch “

/OFF”

Set the switch to “

” to turn on the low

beams, the taillight and the meter lighting.
Set the switch to “

” to turn on the high

beams, the taillight and the meter lighting.
Set the switch to “OFF” to turn off all the lights.

U5VH10.book Page 4 Thursday, May 16, 2002 2:18 PM

Summary of Contents for KODIAK Ultramatic


























































































































































































Search results

Summary of Contents for KODIAK Ultramatic

Reviews:

Related manuals for KODIAK Ultramatic

Brands by name

Popular brands

Yamaha KODIAK Ultramatic, Owner'S Manual

Search results

Summary of Contents for KODIAK Ultramatic

Reviews:

Related manuals for KODIAK Ultramatic

Brands by name

Popular brands