Yamaha KODIAK 450 Owner'S Manual Download Page 87 | Manualshive

Page: 87 / 190

Yamaha KODIAK 450 Owner'S Manual Download Page 87

7-15

Exhaust system

The exhaust system on the ATV is very hot
during and following operation. To prevent
burns, avoid touching the exhaust system.
Park the ATV in a place where pedestrians or
children are not likely to touch it.

WARNING

POTENTIAL HAZARD
Hot exhaust system.
WHAT CAN HAPPEN
Dry grass or brush or other combustible
material accumulated around the en-
gine area could catch fire.
Someone touching the exhaust system
during or after operation could be
burned.
HOW TO AVOID THE HAZARD
Do not operate, idle, or park the ATV in
dry grass or other dry ground cover.
Keep the engine area free of dry grass,
brush, or other combustible material.

Do not touch the hot exhaust system.
Do not park the ATV in a place where
others might be likely to touch it.

U5ND11.book Page 15 Wednesday, April 30, 2003 1:52 PM

«
...
85
86
87
88
89
...
»

Summary of Contents for KODIAK 450































































































































































































Reviews:

No comments