manualshive.com logo in svg

Yamaha KODIAK 450, Owner'S Manual, Page: 136 / 190

Share
Download
Yamaha KODIAK 450 Owner'S Manual Download Page 136

8-23

EBU12572

Changing the coolant

1. Place the ATV on a level surface.
2. Remove panels E and F. (See pages

8-10–8-11 for panel removal and installa-
tion procedures.)

3. Place a container under the engine, and

then remove the coolant drain bolt. (Use
a trough or a similar object as shown to
prevent coolant from spilling on the foot-
rest.)

1. Coolant drain bolt

WARNING

POTENTIAL HAZARD 
Removing the radiator cap when the en-
gine and radiator are still hot. 
WHAT CAN HAPPEN 
You could be burned by hot fluid and
steam blown out under pressure. 
HOW TO AVOID THE HAZARD 
Wait for the engine to cool before re-
moving the radiator cap. Always use a
thick rag over the cap. Allow any re-
maining pressure to escape before
completely removing the cap.

U5ND11.book  Page 23  Wednesday, April 30, 2003  1:52 PM

Summary of Contents for KODIAK 450































































































































































































Reviews:

No comments