manualshive.com logo in svg

Yamaha KODIAK 450, Owner'S Manual, Page: 162 / 190

Share
Download
Yamaha KODIAK 450 Owner'S Manual Download Page 162

8-49

EBU00385

Battery maintenance

1. When the machine is not used for a

month or longer, remove the battery and
store it in a cool, dark place. Completely
recharge the battery before reinstallation.

CAUTION:

A special battery charger (constant volt-
age/ampere or constant voltage) is re-
quired for recharging a sealed-type
battery. Using a conventional battery
charger may shorten the battery life.

2. Always make sure the connections are

correct when putting the battery back in
the machine.

EBU00876

Fuse replacement 

1. The main fuse case and the fuse box are

located under the seat.

2. If a fuse is blown, turn off the main switch

and install a new fuse of the specified
amperage. Then turn on the switches. If
the fuse immediately blows again, con-
sult a Yamaha dealer.

U5ND11.book  Page 49  Wednesday, April 30, 2003  1:52 PM

Summary of Contents for KODIAK 450































































































































































































Reviews:

No comments