manualshive.com logo in svg

Yamaha KODIAK 450, Owner'S Manual, Page: 125 / 190

Share
Download
Yamaha KODIAK 450 Owner'S Manual Download Page 125

8-12

EBU10991

Engine oil and oil filter cartridge

The engine oil level should be checked before
each ride. In addition, the oil must be changed
and the oil filter cartridge replaced at the inter-
vals specified in the periodic maintenance
and lubrication chart.

To check the engine oil level

1. Remove panel F. (See page 8-11 for

panel removal and installation proce-
dures.)

2. Place the ATV on a level surface.
3. Start the engine, warm it up for several

minutes, and then turn it off.

4. Wait a few minutes until the oil settles.
5. Remove the engine oil filler cap and wipe

off the dipstick with a clean rag.

1. Engine oil filler cap

6. Insert the dipstick in the oil filler hole

(without screwing it in), and then remove
it again to check the oil level.

NOTE:

_ 

The engine oil should be between the mini-
mum and maximum level marks. 

_

U5ND11.book  Page 12  Wednesday, April 30, 2003  1:52 PM

Summary of Contents for KODIAK 450































































































































































































Reviews:

No comments