CB348
CB372
CB373
W3702A
W3701A
W3701B
IC371
IC372
IC373
IC37
4
CB375
W3703
CB37
4
CB371
W3702B
CB347
VIDEO (3)
(Side A)
VIDEO (4)
(Side A)
VIDEO (5)
(Side A)
GND
GND
5.5V
5.5V
DIGITAL
(CB43)
OPERATION (11)
(W4505A)(W4505B)
(R, S models)
DIGITAL
(CB55)
OPERATION (1)
(CB403)
VIDEO (1)
(CB346)
+3.3M
1
4
8
5
A
K
R
F1
F2
A
C-5
A
C-5
NC
-VP
E
-VP
DGND
ACPWR_DET
MCPU_N_RST
PRY
DEST
U, C, T, K, A, B, G, F, L, J models
BE
WH
BE
WH
POWER TRANSFORMER
POWER TRANSFORMER
AC IN
5 k-ohms
10 W
R, S models
A
B
C
D
E
F
G
H
I
J
1
2
3
4
5
6
7
88
RX-V471/HTR-4064
Ref no. Location
D3701
C5
D3704
D3
IC371
B4
IC372
C3
IC373
C3
IC374
E3
• Semiconductor Location
注意)
安全対策
・ この製品の内部には高電圧部分があり危険です。修理の際は、絶縁性の手袋を使用するなどの安全対策を行ってください。
・ 下記のコンデンサには電源を OFF にした後も電荷が残り、高電圧が維持されており危険です。修理作業前に放電用抵抗
(5 k Ω /10 W)を下記の各コンデンサの端子間に接続して放電してください。放電所用時間は各々約 30 秒間です。
VIDEO(3)P.C.B. の C3706
Notes)
Safety measures
• Some internal parts in this product contain high voltages and are dangerous. Be sure to take safety measures during servicing, such
as wearing insulating gloves
• Note that the capacitors indicated below are dangerous even after the power is turned off because an electric charge remains and a
high voltage continues to exist there.
Before starting any repair work, connect a discharging resistor (5 k-ohms/10 W) to the terminals of each capacitor indicated below
to discharge electricity.
The time required for discharging is about 30 seconds per each.
C3706 on VIDEO (3) P.C.B.
Summary of Contents for HTR-4064
