manualshive.com logo in svg

Yamaha GRIZZLY 350, Owner'S Manual

Share
Download
Yamaha GRIZZLY 350 Owner'S Manual Download Page 66

7-9

7

Speed limiter

For riders less experienced with this model, the
throttle lever housing is equipped with a speed lim-
iter. The speed limiter keeps the throttle from fully
opening, even when the throttle lever is pushed to
the maximum. Turning in the adjusting screw limits
the maximum engine power available and de-
creases the maximum speed of the ATV. Turning
in the adjusting screw decreases top speed, and
turning it out increases top speed. (See page
4-10.)

Loading and accessories

Use extra caution when riding the ATV with addi-
tional loads, such as accessories or cargo. The
ATV’s handling may be adversely affected. Re-
duce your speed when adding additional loads.

1. Adjusting screw

MAXIMUM LOADING LIMIT

ATV loading limit (total weight of cargo, rider, 
accessories, and tongue):

210.0 kg (463 lb)

Front carrier:

40.0 kg (88 lb)

Rear carrier:

80.0 kg (176 lb)

Storage compartment:

2.0 kg (4 lb)

Trailer hitch:

Pulling load (total weight of trailer and car-
go):

4900 N (500 kgf, 1102 lbf)

Tongue weight (vertical weight on trailer 
hitch point):

147 N (15 kgf, 33 lbf)

U4S212E0.book  Page 9  Thursday, April 17, 2008  9:17 AM

Summary of Contents for GRIZZLY 350







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands