manualshive.com logo in svg

Yamaha GRIZZLY 350, Owner'S Manual

Share
Download
Yamaha GRIZZLY 350 Owner'S Manual Download Page 132

8-42

8

EBU25102

Lubricating the steering shaft 

The steering shaft must be lubricated at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

EBU29170

Battery 

This model is equipped with a VRLA (Valve Regu-
lated Lead Acid) battery. There is no need to check
the electrolyte or to add distilled water. However,
the battery lead connections need to be checked
and, if necessary, tightened.

NOTICE

ECB00620

Never attempt to remove the battery cell seals,
as this would permanently damage the battery.

WARNING

EWB02140

To remove the battery

1. Remove the seat. (See page 4-18.)
2. Remove the battery holding plate by removing

the bolts.

Recommended lubricant:

Lithium-soap-based grease

POTENTIAL HAZARD
Failure to handle batteries or battery electro-
lyte carefully.

WHAT CAN HAPPEN
You could be poisoned. You could be se-
verely burned by the sulfuric acid in battery
electrolyte. Batteries produce explosive gas-
es.
HOW TO AVOID THE HAZARD
Avoid contact with skin, eyes or clothing. Al-
ways shield eyes when working near batter-
ies. Keep out of reach of children.
Antidote:
EXTERNAL: Flush with water.
INTERNAL: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten
egg or vegetable oil. Get prompt medical at-
tention.
EYES: Flush with water for 15 minutes and
get prompt medical attention. Keep batteries
away from sparks, flames, cigarettes or oth-
er sources of ignition. Ventilate when charg-
ing or using in a closed space.

U4S212E0.book  Page 42  Thursday, April 17, 2008  9:17 AM

Summary of Contents for GRIZZLY 350







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands