manualshive.com logo in svg

Yamaha GRIZZLY 350, Owner'S Manual

Share
Download
Yamaha GRIZZLY 350 Owner'S Manual Download Page 128

8-38

8

EBU24752

Brake light switches 

The operation of the brake light switches must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.
The brake light switch for the brake pedal can be
adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.

1. Remove panel A. (See page 8-9.)

TIP

The brake light switch is properly adjusted when
the brake light comes on just before braking takes
effect.

2. Turn the brake light switch adjusting nut while

holding the brake light switch in place. To
make the brake light come on earlier, turn the
adjusting nut in direction (a). To make the
brake light come on later, turn the adjusting
nut in direction (b).

1. Front axle boot (each side)

1. Rear axle boot (each side)

U4S212E0.book  Page 38  Thursday, April 17, 2008  9:17 AM

Summary of Contents for GRIZZLY 350







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands