manualshive.com logo in svg

Yamaha GRIZZLY 350, Owner'S Manual

Share
Download
Yamaha GRIZZLY 350 Owner'S Manual Download Page 115

8-25

8

TIP

The air filter element should be cleaned every 20–
40 hours. It should be cleaned and lubricated more
often if the ATV is operated in extremely dusty ar-
eas. Each time the air filter element maintenance
is performed, check the air inlet of the air filter case
for obstructions. Check the air filter case rubber
joint to the carburetor fittings and the rubber joint
manifold fittings for an air-tight seal. Tighten all fit-
tings securely to avoid the possibility of unfiltered
air entering the engine.

NOTICE

ECB00460

●

Make sure that the air filter element is prop-
erly seated in the air filter case.

●

Never operate the engine with the air filter el-
ement removed. This will allow unfiltered air
to enter the engine, causing rapid engine
wear and possible engine damage. Addition-
ally, operation without the air filter element
will affect carburetor jetting with subsequent
poor performance and possible engine over-
heating.

EBU23882

Cleaning the spark arrester 

Be sure the exhaust pipe and muffler are cool be-
fore cleaning the spark arrester.

1. Remove the bolts.

2. Remove the tailpipe by pulling it out of the

muffler.

3. Tap the tailpipe lightly, and then use a wire

brush to remove any carbon deposits from the
spark arrester portion of the tailpipe and inside
of the tailpipe housing.

1. Bolt
2. Tailpipe

U4S212E0.book  Page 25  Thursday, April 17, 2008  9:17 AM

Summary of Contents for GRIZZLY 350







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands