Yamaha FZ6 Owner'S Manual Download

Page: 91 / 108

SPECIFICATIONS

8-1

Dimensions:

Overall length:

2095 mm (82.5 in)

Overall width:

750 mm (29.5 in)

Overall height:

1210 mm (47.6 in)

Seat height:

795 mm (31.3 in)

Wheelbase:

1440 mm (56.7 in)

Ground clearance:

145 mm (5.71 in)

Minimum turning radius:

2800 mm (110.2 in)

Weight:

With oil and fuel:

FZS6X 207.0 kg (456 lb)
FZS6XC 208.0 kg (459 lb)

Engine:

Engine type:

Liquid cooled 4-stroke, DOHC

Cylinder arrangement:

Forward-inclined parallel 4-cylinder

Displacement:

600.0 cm³

Bore

stroke:

65.5

44.5 mm (2.58

1.75 in)

Compression ratio:

12.20 :1

Starting system:

Electric starter

Lubrication system:

Wet sump

Engine oil:

Type:

YAMALUBE 4, SAE 10W-30 or SAE 20W-
40

Recommended engine oil grade:

API service SG type or higher, JASO
standard MA

Engine oil quantity:

Without oil filter cartridge replacement:

2.50 L (2.64 US qt) (2.20 Imp.qt)

With oil filter cartridge replacement:

2.80 L (2.96 US qt) (2.46 Imp.qt)

Cooling system:

Coolant reservoir capacity (up to the
maximum level mark):

0.25 L (0.26 US qt) (0.22 Imp.qt)

Radiator capacity (including all routes):

2.00 L (2.11 US qt) (1.76 Imp.qt)

Air filter:

Air filter element:

Oil-coated paper element

Fuel:

Recommended fuel:

Unleaded gasoline only

Fuel tank capacity:

19.4 L (5.13 US gal) (4.27 Imp.gal)

Fuel reserve amount:

3.6 L (0.95 US gal) (0.79 Imp.gal)

Fuel injection:

Throttle body:

Manufacturer:

MIKUNI

Type/quantity:

FZS6X 36EIDW-B1/1
FZS6XC 36EIDW-B4/1

Spark plug (s):

Manufacturer/model:

NGK/CR9EK

Spark plug gap:

0.6–0.7 mm (0.024–0.028 in)

Clutch:

Clutch type:

Wet, multiple-disc

Transmission:

Primary reduction system:

Spur gear

Primary reduction ratio:

86/44 (1.955)

Secondary reduction system:

Chain drive

Secondary reduction ratio:

46/16 (2.875)

Transmission type:

Constant mesh 6-speed

110

130

˚F

YAMALUBE 4 (10W-30)
or SAE 10W-30

YAMALUBE 4 (20W-40)
or SAE 20W-40

–10

–20

˚C

U4S811E0.book Page 1 Wednesday, August 8, 2007 1:14 PM

Summary of Contents for FZ6













































































































Search results

Summary of Contents for FZ6

Reviews:

Related manuals for FZ6

Brands by name

Popular brands

Yamaha FZ6, Owner'S Manual

Search results

Summary of Contents for FZ6

Reviews:

Related manuals for FZ6

Brands by name

Popular brands