manualshive.com logo in svg

Yamaha FZ6, Owner'S Manual

Share
Download
Yamaha FZ6 Owner'S Manual Download Page 26

INSTRUMENT AND CONTROL FUNCTIONS

3-8

3

LCD and tachometer brightness
control mode

This function allows you to adjust the
brightness of the LCD and the tachom-
eter panel and needle to suit the out-
side lighting conditions.

To set the brightness

1. Turn the key to “OFF”.
2. Push and hold the “SELECT” but-

ton.

3. Turn the key to “ON”, and then re-

lease the “SELECT” button after
five seconds.

4. Push the “RESET” button to select

the desired brightness level.

5. Push the “SELECT” button to con-

firm the selected brightness level.
The display will return to the odom-
eter or tripmeter mode.

EAU12347

Handlebar switches 

Left

Right

1. Tachometer panel
2. Tachometer needle

3. LCD

4. Brightness level

1. Dimmer switch “

/

”

2. Turn signal switch “

/

”

3. Horn switch “

”

4. Hazard switch “

”

1. Engine stop switch “

/

”

2. Start switch “

”

U4S811E0.book  Page 8  Wednesday, August 8, 2007  1:14 PM

Summary of Contents for FZ6













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands