manualshive.com logo in svg

Yamaha FZ6, Owner'S Manual

Share
Download
Yamaha FZ6 Owner'S Manual Download Page 97

CONSUMER INFORMATION

9-4

9

EAU26560

Motorcycle noise regulation 

TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:

Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other
than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve-
hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of
the vehicle after such device or element of design has been removed or rendered inoperative by any person.
“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW”.
These acts include tampering with the following systems; i.e., modification, removal, etc.

Exhaust system

• Muffler
• Exhaust pipe
• Silencer

Intake system

• Air cleaner case
• Air cleaner element
• Intake duct

U4S811E0.book  Page 4  Wednesday, August 8, 2007  1:14 PM

Summary of Contents for FZ6













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands