Yamaha F9.92 Owner'S Manual Download Page 21 | Manualshive

Page: 21 / 94

background image

Basic components

15

EMU26201

Neutral interlock trigger

To shift out of neutral, first pull the neutral in-
terlock trigger up.

EMU26211

Neutral throttle lever

To open the throttle without shifting into ei-
ther forward or reverse, put the remote con-
trol lever in the neutral position and lift the
neutral throttle lever.

NOTE:

The neutral throttle lever will operate only
when the remote control lever is in neutral.
The remote control lever will operate only
when the neutral throttle lever is in the closed

position.

EMU26221

Choke switch

To activate the choke system, press in the
main switch while the key is turned to the
“

” (on) or “

” (start) position. The

choke system will then supply the rich fuel
mixture required to start the engine. When
the key is released, the choke will switch off
automatically.

EMU25911

Tiller handle

To change direction, move the tiller handle to
the left or right as necessary.

6. Throttle
7. Fully open

1. Neutral interlock trigger

1. Fully open
2. Fully closed

ZMU03160

«
...
19
20
21
22
23
...
»

Summary of Contents for F9.92































































































Reviews:

No comments

Related manuals for F9.92

Brand: Kaba Pages: 16

Brand: IEI Technology Pages: 234

Brand: Lantronix Pages: 8

Brand: Biostar Pages: 61

Brand: Gigabyte Pages: 46

Brand: NXP Semiconductors Pages: 269

Brand: RAK Pages: 17

EmbCore ROM-7421

Brand: Advantech Pages: 25

BrillianX 1S/2000

Brand: QDI Pages: 63

Brand: Octek Pages: 102

Brand: ON Semiconductor Pages: 3

Side-Power SX100/185T

Brand: SLEIPNER MOTOR AS Pages: 16

MBD-X11SDV-4C-TP8F-B

Brand: Supermicro Pages: 123

Brand: Liantec Pages: 4

Brand: Zamel Pages: 3

Brand: DFI Pages: 177

Brand: IEPC Pages: 9

Brand: IEI Technology Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands