Yamaha F9.92 Owner'S Manual Download Page 73

Page: 73 / 94

Maintenance

Checkpoints

●

Check each of the propeller blades for
wear, erosion from cavitation or ventila-
tion, or other damage.

●

Check the propeller shaft for damage.

●

Check the splines / shear pin for wear or
damage.

●

Check for fish line tangled around the pro-
peller shaft.

●

Check the propeller shaft oil seal for dam-
age.

NOTE:

If the shear pin equipped: it is designed to
break if the propeller hits a hard underwater
obstacle to help protect the propeller and
drive mechanism. The propeller will then
spin freely on the shaft. If this happens, the

shear pin must be replaced.

EMU30660

Removing the propeller

EMU29194

Spline models

Straighten the cotter pin and pull it out
using a pair of pliers.

Remove the propeller nut, washer, and
spacer (if equipped).

Remove the propeller and thrust wash-
er.

EMU29212

Dual thrust models

Straighten the cotter pin and pull it out
using a pair of pliers.

ZMU01897

1. Cotter pin
2. Propeller nut
3. Washer
4. Propeller
5. Thrust washer

1. Cotter pin
2. Propeller nut

ZMU02062

ZMU02329

Summary of Contents for F9.92































































































Search results

Summary of Contents for F9.92

Reviews:

Related manuals for F9.92

Brands by name

Popular brands

Yamaha F9.92, Owner'S Manual

Search results

Summary of Contents for F9.92

Reviews:

Related manuals for F9.92

Brands by name

Popular brands