Yamaha F50C Owner'S Manual Download Page 35 | Manualshive

Page: 35 / 114

background image

2-12

E

301011

EMD62110

TOP COWLING LOCK LEVER

To remove the engine top cowling, pull
up the lock lever. Then lift off the cowling.
When replacing the cowling, check to be
sure it fits properly in the rubber seal.
Then lock the cowling again by moving
the lever downward.

000971

EMD60010

TILT SUPPORT LEVER

To keep the outboard motor in the tilted-
up position, lock the tilt support lever to
the clamp bracket.

EMU01546

FLUSHING DEVICE

This device

1

is used to clean the cooling

water passages of the motor using a gar-
den hose and tap water.

NOTE:

Refer to “CLEANING COOLING-WATER
PASSAGES” in Chapter 4 for instructions
on usage.

000280

q

EMU00162

TOP COWLING LOCK LEVER

To remove the engine top cowling, turn
the lock lever. Then lift off the cowling.
When replacing the cowling, check to be
sure it fits properly in the rubber seal.
Then lock the cowling again by moving
the lever upward.

1

Top cowling lock lever

001240

q

F60, T60

F50, T50

62Y-9-1C-2 3/20/03 10:22 AM Page 13

«
...
33
34
35
36
37
...
»

Summary of Contents for F50C



















































































































Reviews:

No comments

Related manuals for F50C

Brand: MSI Pages: 19

Brand: Linear Pages: 10

GeForce 8300 (MI-A78U-8309)

Brand: XFX Pages: 26

Brand: Aaeon Pages: 111

Brand: Memec Pages: 45

Brand: VIA Technologies Pages: 26

R3288LC-2N Series

Brand: JETWAY Pages: 44

Brand: EVGA Pages: 40

Brand: LiteOn Pages: 38

Brand: JETWAY Pages: 58

Brand: C-Control Pages: 8

Brand: PC Chips Pages: 49

Brand: DFI Pages: 38

Brand: Maxim Integrated Pages: 4

Brand: Maxim Integrated Pages: 11

Brand: Maxim Integrated Pages: 21

Brand: Eurotech Pages: 32

Brand: 16XEIGHT Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands