Yamaha F50C Owner'S Manual Download Page 45

Page: 45 / 114

3-6

EMF43510

Engine

Check the engine and engine mounting.

Look for loose or damaged fasteners.

Check the propeller for damage.

Do not start the engine out of water.
Overheating and serious engine damage
can occur.

EMU01436

CHECKING THE ENGINE OIL LEVEL

Put the outboard motor in an upright
position (not tilted).

Pull out the oil dipstick and wipe it
clean.

Completely re-insert the dipstick and
pull out it again.

Check the oil level using the dipstick
to be sure the level falls between the
upper and lower marks. Fill with oil if
it is below the lower mark, or drain to
the specified level if it is above the
upper mark.

Oil dipstick

Lower level mark

Upper level mark

201011*

201012*

62Y-9-1C-3 3/20/03 10:23 AM Page 7

Summary of Contents for F50C



















































































































Search results

Summary of Contents for F50C

Reviews:

Related manuals for F50C

Brands by name

Popular brands

Yamaha F50C, Owner'S Manual

Search results

Summary of Contents for F50C

Reviews:

Related manuals for F50C

Brands by name

Popular brands