Yamaha F50C Owner'S Manual Download Page 52

Page: 52 / 114

3-13

EMG38010

STOPPING ENGINE

Let it cool off for a few minutes at idle or
low speed first. Stopping the engine
immediately after operating at high speed
is not recommended.

EMU00276

PROCEDURE

Main switch equipped model

Turn the main switch to “OFF”.

If the fuel joints are provided, discon-
nect the fuel line from the motor after
stopping the engine.

Tighten the air vent screw on the fuel
tank cap after stopping the engine, if
it is equipped.

Remove the key if the boat will be left
unattended.

NOTE:

The engine can also be stopped by
pulling the lanyard and removing the lock
plate from the engine stop lanyard switch
(then turning the main switch to “OFF”).

304011*

902052

START

OFF

701023

62Y-9-1C-3 3/20/03 10:23 AM Page 14

Summary of Contents for F50C



















































































































Search results

Summary of Contents for F50C

Reviews:

Related manuals for F50C

Brands by name

Popular brands

Yamaha F50C, Owner'S Manual

Search results

Summary of Contents for F50C

Reviews:

Related manuals for F50C

Brands by name

Popular brands