Yamaha F25G Owner'S Manual Download Page 39

Page: 39 / 108

Engine control system

EMU26806

Alert system

ECM00093

Do not continue to operate the engine if
an alert device has activated. Consult
your Yamaha dealer if the problem cannot
be located and corrected.

EMU43754

Overheat alert

This engine has an overheat-alert device. If
the engine temperature rises too high, the
alert device will activate.



The engine speed will automatically de-
crease to 2000–3500 r/min.



The overheat-alert indicator will light or
blink (if equipped).



The buzzer will sound (if equipped on the
tiller handle, remote control box, or main
switch panel).

If the alert system has activated, stop the en-
gine and check the cooling water inlets:



Check trim angle to be sure that the cool-
ing water inlet is submerged.



Check the cooling water inlet for clogging.

EMU26869

Low oil pressure alert

If the oil pressure drops too low, the alert de-
vice will activate.



The engine speed will automatically de-
crease to about 2000–3500 r/min.

ZMU0

ZMU01758

ZMU08744

6FM-28199-75-1E0.book 33 ページ２０１９年１０月３０日　水曜日　午前１１時２３分

Summary of Contents for F25G













































































































Search results

Summary of Contents for F25G

Reviews:

Related manuals for F25G

Brands by name

Popular brands

Yamaha F25G, Owner'S Manual

Search results

Summary of Contents for F25G

Reviews:

Related manuals for F25G

Brands by name

Popular brands