Yamaha F150C Owner'S Manual Download

Page: 24 / 80

Basic components

EMU26340

Tilt support lever for power trim and
tilt or hydro tilt model

To keep the outboard motor in the tilted up po-
sition, lock the tilt support lever to the clamp
bracket.

EMU26381

Top cowling lock lever (pull up type)

To remove the engine top cowling, pull up the
lock lever(s) and lift off the cowling. When in-
stalling the cowling, check to be sure it fits
properly in the rubber seal. Then lock the
cowling by moving the lever(s) downward.

EMU26460

Flushing device

This device is used to clean the cooling water
passages of the motor using a garden hose
and tap water.

NOTE:

For details on usage, see page 43.

EMU26490

Digital tachometer

The tachometer shows the engine speed and
has the following functions.

1. Tilt support lever

1. Flushing device

63P10.book Page 18 Tuesday, May 13, 2003 10:23 AM

Summary of Contents for F150C

















































































Search results

Summary of Contents for F150C

Reviews:

Related manuals for F150C

Brands by name

Popular brands

Yamaha F150C, Owner'S Manual

Search results

Summary of Contents for F150C

Reviews:

Related manuals for F150C

Brands by name

Popular brands