manualshive.com logo in svg

Yamaha F150C, Owner'S Manual

Share
Download
Yamaha F150C Owner'S Manual Download Page 60

Maintenance

54

2.

Operate each of the power trim and tilt
switches on the remote control and en-
gine bottom cowling (if equipped) to
check that all switches work.

3.

Tilt the outboard motor up and check that
the tilt rod and trim rods are extended
completely.

4.

Use the tilt support lever to lock the motor
in the up position. Operate the tilt down
switch briefly so the motor is supported
by the tilt support lever.

5.

Check that the tilt rod and trim rods are
free of corrosion or other flaws.

6.

Activate the tilt-down switch until the trim
rods have retracted completely into the
cylinders.

7.

Activate the trim-up switch until the tilt rod
is fully extended. Unlock the tilt support
lever.

8.

Tilt the outboard motor down. Check that
the tilt rod and trim rods operate smooth-
ly.

NOTE:

Consult your Yamaha dealer if any operation
is abnormal.

EMU29170

Checking propeller

WARNING

EWM00320

You could be seriously injured if the en-
gine accidentally starts when you are near
the propeller.

●

Before inspecting, removing, or install-
ing the propeller, remove the spark plug
caps from the spark plugs. Also, place
the shift control in neutral, turn the main
switch to 

 (off) and remove the key,

and remove the lanyard from the engine
stop switch. Turn off the battery cut-off
switch if your boat has one.

●

Do not use your hand to hold the propel-
ler when loosening or tightening the
propeller nut. Put a wood block between
the anti-cavitation plate and the propel-
ler to prevent the propeller from turning.

1. Tilt rod
2. Tilt support lever

3. Trim rods

63P10.book  Page 54  Tuesday, May 13, 2003  10:23 AM

Summary of Contents for F150C

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands